⭐⭐⭐⭐⭐ AUSTRALIA’S LARGEST RANGE OF NATURAL STONE PAVERS ⭐⭐⭐⭐⭐
Call: 03 9706 9767
Mon-Fri 7:30am - 5pm / Sat 9am - 4pm
Menu
⭐⭐⭐⭐⭐ AUSTRALIA’S LARGEST RANGE OF NATURAL STONE PAVERS ⭐⭐⭐⭐⭐
Mon-Fri 7:30am - 5pm / Sat 9am - 4pm
From $17.60 / each
Raven Grey Granite Pavers with Sawn Edges are available in varieties of sizes. Granite can be sealed with an invisible penetrating sealer to assist in the ongoing clean up of the stone. These tiles have had 3 coats of colour enhancing sealer from TASMAN to darken them. It is an additional purchase. Thickness and size variation is the industry standard of +-2mm.
Matching Pool Copings: Raven Grey Granite Pavers with Bullnose Edges, Raven Grey Granite Pavers with Drop Face
other sizes available by request, or we can cut down existing sizes to suit
12mm :Thick tiles should be laid directly onto a concrete slab or great for balconies, decks or indoor floor tiles.
20mm :Thick pavers can be laid as above OR onto a compacted road base into a wet slurry of sand and cement
30mm :Thick pavers can be laid as both above or onto a compacted road base into a dry sand bed, great for tiling over easements or where you require water permeation.
We deliver Crazy Paving door to door to all suburbs in Melbourne, Sydney, Canberra, Brisbane, Adelaide and Hobart. We also deliver to any regional area in Australia at reasonable freight rates.
Granite is a perfect choice for…
For more information feel free to give us a call on 03 9706 9767 or Talk to one of our experts and get a FREE Quote.
| SIZES + PRICES: | 500x500x20mm (piece) (Raven Grey), 800x400x20mm (piece) (Raven Grey) |
|---|
Granite can be sealed with an invisible penetrating sealer to assist in the ongoing clean up of the stone.
An invisible penetrating sealer can be applied prior to grouting which will facilitate easy clean up after application of the grout.
Cleaning:
Do not use Hydrochloric acid for clean up as this can cause minerals present in the stone to react.
Maintenance:
Just sweep when needed. Granite responds well to high pressure cleaning. A solution of mild detergent and water, can be applied prior to pressure cleaning.
Installation Tips:
Please ensure ALL grout lines are completely dry and the tiles are completely dry prior to applying the grout. IF you don’t you may end up with shading occuring on the tiles surface due to the trapped excessive moisture still present and then ADDED to during the grouting process. (This may disappear over a full cycle of the seasons). BUT to guarantee this doesn’t occur we would recommend NOT grouting if the tiles are damp and the grout joints contain residual water. ALSO try to use a dryer grout mix. IF unsure please ring us for FREE advice. If laying in adhesive we recommend ONLY using a rapid setting grey adhesive like Mapei Granirapid Grey.IF laying in sand and cement please ONLY use Grey cement to ensure no shadowing comes through the stone and you must seal the back of the tile prior to installation ( Call if you need further instructions). And For permanently installed tiles (using Adhesive OR Sand and Cement) the only guaranteed sustainable way to protect the stone from stains caused by rust, efflorescence, water stains migrating from the installed back of the tile from the bedding mix, is sealing with special two component coating material (e.g. AKEMI AKEPOX® 2015 Anti-Stain). IF you do not want to follow these instructions PLEASE at least lay 2 tiles in your desired fashion and inspect 24hrs later and ensure they look EXACTLY like the remaining uninstalled tiles before proceeding. Interesting INDEPENDENT article regarding improper installation techniques and the associated long term problems, most of which we have covered above https://www.pavingexpert.com/stain_reflective_01
